Problem with the SD lector

Hello, I have a problem with the sd reader and the factory marlin. I asked the firmware to Lucy and try a thousand ways to configure the SD but nothing, also buy the original lcd + sd but without results. I need help, I have the SD configured like this.


//LCD and SD support

#define ULTRA_LCD //general LCD support, also 16x2

//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)

#define SDSUPPORT // Enable SD Card Support in Hardware Console

//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)

//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication

//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder

//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking

//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.

//#define ULTIPANEL //the UltiPanel as on Thingiverse

//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click

//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click



// The MaKr3d Makr-Panel with graphic controller and SD support

// reprap.org/wiki/MaKr3d_MaKrPanel

//#define MAKRPANEL



// The RepRapDiscount Smart Controller (white PCB)

// reprap.org/wiki/RepRapDiscount_Smart_Controller

#define REPRAP_DISCOUNT_SMART_CONTROLLER



// The GADGETS3D G3D LCD/SD Controller (blue PCB)

// reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel

//#define G3D_PANEL



// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB)

// reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller

//

// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: code.google.com/p/u8glib/wiki/u8glib

//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER



// The RepRapWorld REPRAPWORLD_KEYPAD v1.1

// reprapworld.com/?products_details&products_id=202&cPath=1591_1626

//#define REPRAPWORLD_KEYPAD

//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click



// The Elefu RA Board Control Panel

// www.elefu.com/index.php?route=product/product&product_id=53

// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: github.com/kiyoshigawa/LiquidCrystal_I2C

//#define RA_CONTROL_PANEL



//automatic expansion

#if defined (MAKRPANEL)

#define DOGLCD

#define SDSUPPORT

#define ULTIPANEL

#define NEWPANEL

#define DEFAULT_LCD_CONTRAST 17

#endif



#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)

#define DOGLCD

#define U8GLIB_ST7920

#define REPRAP_DISCOUNT_SMART_CONTROLLER

#endif



#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)

#define ULTIPANEL

#define NEWPANEL

#define ENCODER_PULSES_PER_STEP 4

#define ENCODER_STEPS_PER_MENU_ITEM 1

#endif



#if defined(REPRAPWORLD_KEYPAD)

#define NEWPANEL

#define ULTIPANEL

#endif

#if defined(RA_CONTROL_PANEL)

#define ULTIPANEL

#define NEWPANEL

#define LCD_I2C_TYPE_PCA8574

#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander

#endif



//I2C PANELS



//#define LCD_I2C_SAINSMART_YWROBOT

#ifdef LCD_I2C_SAINSMART_YWROBOT

// This uses the LiquidCrystal_I2C library ( bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )

// Make sure it is placed in the Arduino libraries directory.

#define LCD_I2C_TYPE_PCF8575

#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander

#define NEWPANEL

#define ULTIPANEL

#endif



// PANELOLU2 LCD with status LEDs, separate encoder and click inputs

//#define LCD_I2C_PANELOLU2

#ifdef LCD_I2C_PANELOLU2

// This uses the LiquidTWI2 library v1.2.3 or later ( github.com/lincomatic/LiquidTWI2 )

// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.

// (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)

// Note: The PANELOLU2 encoder click input can either be directly connected to a pin

// (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).

#define LCD_I2C_TYPE_MCP23017

#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander

#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD

#define NEWPANEL

#define ULTIPANEL



#ifndef ENCODER_PULSES_PER_STEP

#define ENCODER_PULSES_PER_STEP 4

#endif



#ifndef ENCODER_STEPS_PER_MENU_ITEM

#define ENCODER_STEPS_PER_MENU_ITEM 1

#endif





#ifdef LCD_USE_I2C_BUZZER

#define LCD_FEEDBACK_FREQUENCY_HZ 1000

#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100

#endif



#endif



// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs

//#define LCD_I2C_VIKI

#ifdef LCD_I2C_VIKI

// This uses the LiquidTWI2 library v1.2.3 or later ( github.com/lincomatic/LiquidTWI2 )

// Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.

// Note: The pause/stop/resume LCD button pin should be connected to the Arduino

// BTN_ENC pin (or set BTN_ENC to -1 if not used)

#define LCD_I2C_TYPE_MCP23017

#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander

#define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)

#define NEWPANEL

#define ULTIPANEL

#endif



// Shift register panels

// ---------------------

// 2 wire Non-latching LCD SR from:

// bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection



//#define SAV_3DLCD

#ifdef SAV_3DLCD

#define SR_LCD_2W_NL // Non latching 2 wire shiftregister

#define NEWPANEL

#define ULTIPANEL

#endif





#ifdef ULTIPANEL

// #define NEWPANEL //enable this if you have a click-encoder panel

#define SDSUPPORT

#define ULTRA_LCD

#ifdef DOGLCD // Change number of lines to match the DOG graphic display

#define LCD_WIDTH 20

#define LCD_HEIGHT 5

#else

#define LCD_WIDTH 20

#define LCD_HEIGHT 4

#endif

#else //no panel but just LCD

#ifdef ULTRA_LCD

#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display

#define LCD_WIDTH 20

#define LCD_HEIGHT 5

#else

#define LCD_WIDTH 16

#define LCD_HEIGHT 2

#endif

#endif

#endif



// default LCD contrast for dogm-like LCD displays

#ifdef DOGLCD

# ifndef DEFAULT_LCD_CONTRAST

# define DEFAULT_LCD_CONTRAST 32

# endif

#endif